10/100Base TX to 100Base FX Media Converter
General Description
The media converter transforms the transmission media of Ethernet signal from CAT5 to optical fiber. it can extend the transmission distance to several kilometers or hundred kilometers.Using media converter is an economical solution to achieve long distance transmission based on current status.
Key Features
In conformity to IEEE 802.3 10 Base-T standard.
In conformity to IEEE 802.3u 100 Base-TX/FX standard.
Support CSMA/CD Protocol.
Built in 128Kb RAM for data buffer.
Back pressure flow control for full duplex, IEEE802.3 X and half duplex.
Automatic identification of MDI/MDI-X cross line.
Forward 1600 bytes packets for management. Can also reach 9k bytes(optional, Must inform us ahead).
Supports link fault pass through function.
Supports far end fault function.
Power from external power adapter or USB port.
Fiber connector: Choice from SC,ST,FC or LC connector for multimode and single mode.
DIP Switch to set configurations.
Built in a watchdog timer to monitor internal switch error.
LED display for link/activity, full/half,10M/100M.
Transmission distance can reach 2km for multimode and 120KM for single mode.
Can be rack mounted in 14 slots chassis(external Power supply).
Support 4KV lighting protection(external power supply, Optional).
Technical Parameter
|
|
10/100M Multimode Media converter |
10/100M Single Media converter |
|
Cable |
MM fiber/twist pair |
SM fiber/twist pair |
|
Operation Mode |
full duplex mode or half duplex mode |
|
|
Connector |
One UTP RJ-45connector,oneSC/ST/FC or one LC connector |
|
|
Power Supply |
outside: 5V DC 1A built-in: 110-265V AC or 48V DC or 12V DC(optional) |
|
|
Data Buffer |
128Kb |
|
|
Environmental temperature |
0~60 degrees |
|
|
Transfer Fiber |
multi-mode: 50/125, 62.5/125 or 100/140μm single mode:: 8.3/125, 8.7/125, 9/125 or 10/125μm |
|
|
Relative Humidity |
5%-90% |
|
|
Size |
94mm x 71mm x 26mm (Power external type) 160mm x 129mm x 33mm(Power internal type) |
|
LED indicator lamps
|
LED indicator lamp |
Status |
Explanation |
|
FX Link/Act |
On |
Connection status display for fiber link. “ON” indicates that Fiber link is in correct connection. |
|
Blink |
Active status display of fiber link “Blink” indicates packet goes through Fx end. |
|
|
TP Link/Act |
On |
Connection status display for electric link. “ON” indicates that electric link is in correct connection. |
|
Blink |
Active status display of electric link “Blink” indicates packet goes through Tx end. |
|
|
DUP |
On |
Transceiver works in the full duplex mode. |
|
Off |
Transceiver works in the half duplex mode. |
|
|
PWR |
On |
Power is on and normal. |
|
SD |
On |
Fiber signal is detected. |
|
100 |
On |
Transfer rate of electric interface is 100Mbps. |
|
Off |
Rate of electric interface is 10Mbps |
Transmission characteristics of single and dual fiber transceiver
|
Dual fiber |
Interface |
Wavelength(nm) |
Transmitting optical power (dBm) |
Receving sensitivity(dBm) |
Transmission distance(km) |
Loss allowed(dBm) |
|
MM |
ST/SC/FC |
1310 |
-14 ~ -9 |
-34 |
2 |
10 |
|
SM |
ST/SC/FC |
1310 |
-13 ~ -4 |
-33 |
20 |
19 |
|
SM |
SC |
1310 |
-8 ~ -3 |
-35 |
40 |
27 |
|
SM |
SC |
1310 |
-5 ~ 0 |
-36 |
60 |
34 |
|
SM |
SC |
1550 |
-5 ~ 0 |
-36 |
80 |
27 |
|
SM |
SC |
1550 |
-5 ~ 0 |
-36 |
100 |
31 |
|
SM |
SC |
1550 |
-2 ~ 3 |
-37 |
120 |
35 |
|
|
||||||
|
Single fiber |
Interface |
Wavelength(nm) |
Transmitting optical power (dBm) |
Receving sensitivity(dBm) |
Transmission distance(km) |
Loss allowed(dBm) |
|
SM |
SC |
1310/1550 |
-12 ~ -3 |
-35 |
20 |
Standard loss:1310nm 0.4/km 1550nm 0.25/km |
|
SM |
SC |
1310/1550 |
-8 ~ -3 |
-35 |
30 |
|
|
SM |
SC |
1310/1550 |
-5 ~ 0 |
-36 |
40~60 |
|
|
SM |
SC |
1310/1550 |
-3 ~ 3 |
-36 |
60~80 |
|
DIP function(only for external power supply):
DIP1:"ON" enable LFP alarm function, "OFF" disable LFP function;
DIP2:"ON" force TX port work under 10M,"OFF" force TX port work under auto negotiation;
DIP3:"ON" force TX port work under 10M,"OFF" force TX port work under 100M;
DIP4:"ON" force TX port work under Half Duplex, "OFF" force TX port work under Full
Duplex.
DIP function(only for card type, internal power supply):
DIP1:"ON" enable LFP alarm function, "OFF" disable LFP function;
DIP2:"ON" force TX port work, "OFF" force TX port work under auto negotiation;
DIP3:"ON" force TX port work under 10M,"OFF" force TX port work under 100M;
DIP4:"ON" force TX port work under Half Duplex, "OFF" force TX port work under Full Duplex;
DIP5:"ON" force fiber port work under Half Duplex, "OFF" force fiber port work under Full Duplex;
DIP6:"ON" fiber port and TX port are not compliance to IEEE802.3X protocol, "OFF" fiber port and TX port are not compliance to IEEE802.3X protocol.
DIP7 and DIP8:
Both are "OFF", work under the storage and forward exchange mode(default mode);
DIP7“ON” and DIP8 OFF”, work under the improved quick exchange mode;
DIP7 "OFF" and DIP8 "ON", work under converter mode, no date storage, TX must be forced to be 100M;
Both are "ON", work under converter mode, automatically convert to forward mode when the speed of optical ports and TX port.
XPON Passive Optical Network
snowthinktides
0755-83068027
sales@thinktides.com